Firmware upload error
I will replace it.
Thanks a lot.
hey zax, i just purchased your software yesterday, i installed right away grbl “e” from the menu. All worked just fine, got a message that grbl e is ready etc. i tried moving motors by using arrows and it worked well.
Then i tried to flash grbl “f” high freq pwm because the laser i ordered is ttl/pwm. I am very new in these things so i dont know if that laser would benefit from that grbl version, but i tried it. I thought that i can reflash grbl”e” back after. Boy i was wrong. No matter what i try, i keep getting “upload error 1/1” and cant see any flash progress, just another black window with some weird letters and numbers appears with the error message right after.
Funny thing is that i can still connect laser, it still says that grbl “f” is ready and i can use laser.
Is there ANY way how to reflash the controller board with grbl - e if i will experience any problems with current f version? Btw clear eeprom did not worked. Got the very same upload error 1/1 message.
Thanks in advance!
A genuine Arduino Nano can be flashed hundreds of times, but the latest Chinese clones (not using an Atmel microcontroller) have memory issues and are easy to corrupt. If you have another "Nano" you can use it to re-write the boot loader which may help. Sometimes they will work after letting them cool down for a while.
There's actually nothing wrong with using that firmware, it's the same as the default Grbl 1.1e except it was compiled with 7.8kHz PWM (instead of the standard 0.98kHz). I would just leave it "as is".
Thanks a lot for quick response. Tbh i am pissed. You buy something, it works once and then it doesnt because chinese dont give a s*it about quality.
Was browsing amazon and i am wondering if this arduino
Would work. If yes all i have to do is just swap the old broken one with the one linked above? Or is extra soldering required?
The thing is i really wanna solve this issue because i get “connected and grbl ready” message now. But one day.... and i am screwed
P.s. i have to correct one thing. It was “grbl-f xy home sv” what i tried to flash over grbl-e. And it failed. Well failed - it says grbl-f is ready so... but i couldnt reflash it again with “grbl-f pwm” or anything else.
zax please can you tell me if this is nano with genuine atmel or just cheap chinese knockoff?
i know i see the logo but you never know.
i tried to change usb cable - didnt work
i tried to use arduino ide software - didnt work
i tried another computer - didnt work
i tried to use xloader - didnt work
honestly if this is genuine atmel i have no idea what is going on then. i just cant upload any grbl no matter what. btw when connected, that red light doesnt blink at all. it is fully on. is it good thing or bad?
in arduino ide i get this error
avrdude: stk500_disable() : protocol error, expect =0x14, resp = 0x95
thanks in advance!
what way can i reset nano please?
@Zax He could use a Duinotech NANO board -ARDUINO COMPATIBLE. The chipset used is a ATMega328P & FT232RL. Can be purchase from https://www.jaycar.us catelogue number XC4414, but the price is not so cheap it around $21 US for one.
@LogansRun basically i just have to swap mine broken one with the new nano(compatible) one? Nothing else?
No extra soldering etc?
@redcore Almost all of them are clones, unless you purchase direct from Arduino.
The genuine Arduino Nano uses an ATMega328p microcontroller and FT232 UART, the clones often replace the FT232 with a CH340 (Chinese UART) but I don't have a problem with that as they seem stable.
The latest Eleks Nano is using a Chinese clone microcontroller and they seem to have a lot of problems with memory and overheating.
So that said, all Nano's are pin compatible and can be used interchangeably, plug and play. Just make sure you get one with soldered pins AND a boot loader unless you know how to install it yourself (it's pretty simple).
Would this one work for me?
They say its with bootloader and its soldered.
@redcore I don't see why not.
hello just had the same problem. i m running a eleksmaker a3 pro with atmel 328p . i was burning stuff for work when i decided to move back from 1f pwm to 1f laser axe.
in the mean time i restarted my computer and t2 laser did an upgrade.
i flashed the rom and then at the end i had this error message . since i can only make the laser go in one streight line what ever i do and whatever the rom i try to flash or even if i try to errase the rom i get error message firmware upload error.
@znourf Why would you load LaserAxe firmware if you have an EleksMaker board? If you corrupted the Nano then you need to use Arduino IDE to reset the boot loader.
Simply because the laser axe allowed me to modify speed and laser power real time . Anyway , just found out that a spider had made it's "nest" on the nano clone
So the bootloader must have a problem.
Now i've got a uno and wanted to charge the nano clone but there is no ICSP on the clone.
Anyone has an idea of the pining i should use to upload the bootloader to this "clone"
@znourf You can load it directly from Arduino IDE, no need for ICSP or programmer.
My default Grbl 1.1e or any of my Grbl 1.1 builds will allow real time overrides, the laseraxe firmware drives different pins for the axis so only works on their v2 boards (the latest v3 works with standard Grbl pins).
i tried that and got this with a clear eeprom command
avrdude: verification error, first mismatch at byte 0x0002
0x9c != 0x5c
avrdude: verification error; content mismatch
avrdude: verification error; content mismatch
@znourf I know this is for an Uno but exact same procedure with Nano.
okay so i managed to save the arduino clone and even bought 2 others just in case. And today it's back to square one but all 3 are corrupt.
So what happened? I was trying to launch a vector when the engraver set off and immediately stoped with the laser on at full power. I stoped the laser by turning it to low power mode with the switch then moved out to turn everything off.
I turned the mana back on and nothingw as responding . I sent out to try an other nano clone but the same happened . Finally after trying to get it to work i tried a new mana board with a new nano clone. I didn't even have time for it to launch the laser stayed on. But this time the nano has the red light on al the time and gets hot.
@znourf Sorry, I have no idea what is going on with your machine. I have dozens of Nano's for different projects and never had any go crazy like you are saying. They are very reliable and I've found them extremely difficult to kill, even with poor ESD handling they don't seem to fail.