Replacing the Laser Power Supply 12v 5amp to 12v 16amp



  • 0_1511319605637_Dell EP071350-Pinout-1.jpg @ThothLoki
    Here is the pinout of the power supply. Please explain what you mean by "include all of the wires..."



  • @MrLRichards that power supply will supply 16A distributed over those three pins you marked out. One pin will not give you 16A (or at least not safely). My suggestion is to take those three pins' wires (from the connector that goes in there and wire nut them together. That will give you the full 16A.

    The wires I was talking about was with an ATX power supply (PC power supply) that has 12-24 wires for 12V.


  • ElekMaker Develop Department

    yes , that is no problem , but you need make sure your 12V 16A power supply voltage is under 13V



  • I agree with @EleksMaker-Z . When it has no load, a 12V supply can be up to 13-14.5V



  • @ThothLoki Understood. One last question... As it connect the 3 pins is using 1 ground pin ok? or all 3 of those needed as well? Ok that was 2 last questions. :)



  • So I test the voltage once they are all connected and if they are over 13v I would need a regulator of some sort to bring it back down?



  • @MrLRichards yes and no. The reason that they distribute the amperage between multiple pins is the wiring connections inside the power supply is a smaller gauge than what 16A should be going through. I would recommend you use three pins and wire nut them together as well to keep the wires from the potential of heating up


  • ElekMaker Develop Department

    @MrLRichards
    one ground is okey , because our machine are use single GND net



  • @EleksMaker-Z careful. you do not want 16A going through one ground wire on a server power supply with 18-22awg wire. That will overheat the wire pretty quick.

    Safe bet is for every wire you use, you use an equal amount of GND wires


  • ElekMaker Develop Department

    yes but our machine maximum current is under 5A , so dont worry , there wont be more then 5A for our machine



  • @EleksMaker-Z sorry. I miss understood what you had said. I thought you were still talking about the server power supply. I am still using the power supply that came with my machine and have not had the need to upgrade, so thank you.



  • @EleksMaker-Z The laser I am using was purchased from Ebay. It's a 15W laser with an external board that has a TTL connection to the Mana SE. It came with a 12V 5amp power supply but the cables are now too short since I have extended the axis. @ThothLoki I do understand that for each (+) I should have equal number of (-). So my plan is to wire nut the 3 12V(+) together and the 3 (-) together but then there will be a 24awg wire coming from each of those to the laser's (+) and (-) input respectively. Am I on the right track?



  • @MrLRichards That should work. 24Awg wire should be good for up to 3.5A and you will be supplying less than 1A

    P=I*E

    5.5(w) = 12v * E(amps)
    5.5/12 = 0.458Amps



  • @ThothLoki what would I need to do to get the full 16amps?


  • Developer of T2Laser Software

    @ThothLoki That would assume the laser is 100% efficient at converting electrical energy into light, which of course it isn't. A typical 6W diode requires 2.0~2.5A for full output the rest is turned into heat.

    @MrLRichards Your "15W" laser is almost certainly an over-driven 6W, in fact they probably state that 15W is the pulsed output and it probably has a terrible duty cycle so when you run it at full output in CW mode it will fail very quickly due to overheating. This is why I recommend EleksMaker lasers, they don't over drive them to death.



  • @zax I totally agree and did not take inefficiency into account. Just used basic ohms law math


  • Developer of T2Laser Software

    @ThothLoki Your answer was still correct, the 24AWG would be fine.


  • Developer of T2Laser Software

    This post is deleted!


  • @Zax So, I guess my best selection would be the EL02 Laser Module? My hope is to be able to cut plywood and balsa wood which I am sure it would have no problem cutting...


  • Developer of T2Laser Software

    @MrLRichards Air assist (either a fan or preferably a small compressor) and raised platform will significantly improve the cutting capability. What thickness materials are you wanting to cut?


Log in to reply
 

Looks like your connection to Offical Forum was lost, please wait while we try to reconnect.