I saw demo videos but I wanted to get the demo files to use a a basis for new designs. Are any files available?

MItchcecg
@MItchcecg
Posts made by MItchcecg
-
Any Sample files available ?
-
RE: So Disappointed
OK ALL I HAVE IT WORKING
I received it with a bad servo and a bad stepper motor. Since Banggood was of little help I ordered both from amazon after replacing them all seemed to work but the pen up and down was reversed. I finally realized that I built the assembly backwards. Since I am an electronics Engineer and not a mechanical one I was looking for electrical problems (silly me ) anyway it is now working. I just should get replacement parts from Banggood for the defective ones that came with the unit.
-
RE: Gcode m3 and m5 seem to be reversed
thanks for the thought I actually built that section backwards (best way I can describe it) went online and saw a demo of it running which showed the servo on the other side I just flipped it all around and it works fine
THANK YOU all for the assist
-
RE: Gcode m3 and m5 seem to be reversed
nottingham82 Thanks for the insight
I have downloaded the eval of T2 and followed your instructions but I am in the same place for some reason the pen is reversed of what it should be doing laser on the pen is up and laser off the pen is down.
I still need to solve this issue... very frustrated
THANX
MITCH -
RE: Gcode m3 and m5 seem to be reversed
Thanks for getting back to me. I do not know why but mine is backwards and therefore does not work
does anyone know of a solution
-
RE: Gcode m3 and m5 seem to be reversed
I loaded ver 3.8 of the firmware is there somthing else to do other than select egg in elekscam?
-
Gcode m3 and m5 seem to be reversed
When m3 is executed it lifts the pen from the egg and m5 places it on the egg. That seems backwards to me could someone please let me know
THANX
MITCH -
EGG just does not work even invested in parts from other sources NG Help
this is to let you know that I cannot get the egg working properly and below are previous posts FYI. please help solve all of the issues
Just got it yesterday!! Even though there were parts missing I was able to get them at my local hardware store. The build was easy but I had to locate all the instructions on youtube. The eleksmaker site did not display videos properly in 4 different browsers on 3 different computers. SO I could not get any directions from them! Anyway I Installed the EleksCAM software on win10 creators and the software shows the splash screen and then disappears nothing after that. AS I am typing this I just heard a noise and smoke came out of the unit and the motors are just moving on their own. Removed power and reapplied it is just moving the motors and making noise... NOT HAPPY AT ALL
So Disappointed
I have not received response to my direct email so I am using paypal to track communication.SUMMERY
- SOFTWARE THAT DRIVES THE NIT DOES NOT RUN
- THE CIRCUT BOARD SMOKES AND MAKES NOISES AFTER IT WAS PLUGGED IN FOR 15 MINUTES
READ MORE BELOW - not super important but the price onm your site is now $10 less than I paid
Just got it yesterday!! Even though there were parts missing I was able to get them at my local hardware store. The build was easy but I had to locate all the instructions on youtube. The eleksmaker site did not display videos properly in 4 different browsers on 3 different computers. SO I could not get any directions from them! Anyway I Installed the EleksCAM software on win10 creators and the software shows the splash screen and then disappears nothing after that. AS I am typing this I just heard a noise and smoke came out of the unit and the motors are just moving on their own. Removed power and reapplied it is just moving the motors and making noise... NOT HAPPY AT ALL
nottingham82 thanks for the reply. Unfortunately after the unit was plugged in for about 15 minutes nothing sent to the unit just power, it made a funny noise so I looked at it and smoke was coming out and the motors were moving. now the new unit has a dead board and I have gotten no response from the point of purchase Bang Good about the issue
am having similar problems with Banggod to the point I purchased a servo and steepper motor from amazon for my ELeksEgg just to prove the parts were bad that I had gotten in my original kit. to date I cannot create any image on the egg.
I have asked for help and gotten none. they keep asking for more and more videos they wanted to see the connections I sent them photos they want video of connections WHY??? makes no sense. Anyway even after getting the unit working with my own purchased parts the thing does not work well enough to print on an egg I want to return it and get my money back or have a human from eleksmaker call me and solve the issues -
RE: So Disappointed
am having similar problems with Banggod to the point I purchased a servo and steeper motor from amazon for my ELeksEgg just to prove the parts were bad that I had gotten in my original kit. to date I cannot create any image on the egg.
I have asked for help and gotten none. they keep asking for more and more videos they wanted to see the connections I sent them photos they want video of connections WHY??? makes no sense. Anyway even after getting the unit working with my own purchased parts the thing does not work well enough to print on an egg I want to return it and get my money back or have a human from eleksmaker call me and solve the issues